Frigidaire 242018303 Refrigerator Condenser Fan Motor Assembly Genuine OEM Part (Open box)

Frigidaire 242018303 Refrigerator Condenser Fan Motor Assembly Genuine OEM Part (Open box).

Frigidaire 242018303 Refrigerator Condenser Fan Motor Assembly

Genuine OEM Lower Machine Compartment Heat-Exchanger Fan Motor

📝 Product Overview

The Frigidaire 242018303 is a factory-original replacement condenser fan motor for residential refrigerators and freezers. Mounted securely on a structural bracket panel inside the lower rear machine compartment chassis next to the compressor dome, this genuine OEM electric motor serves as the primary dynamic air-mover for your appliance's high-temperature thermal rejection grid.

As an Authentic Frigidaire Electromechanical Component , this motor is specifically engineered to drive the condenser fan blade assembly. When the refrigerator's control system calls for cooling, power is routed to this motor to draw ambient room air through the rear access grill, blowing it directly across the hot condenser coils and the compressor housing shell. This process forces the high-pressure refrigerant gas to reject its heat and condense back into a liquid state, sustaining the thermodynamic refrigeration cycle. Choosing a genuine factory condenser fan motor ensures exact electrical impedance matching to prevent computer board relay failures, delivers the precise RPM requirements to avoid high-head-pressure compressor stalling, and guarantees whisper-quiet, vibration-free operation inside the lower cabinet.

🔍 Signs Your Refrigerator Condenser Fan Motor Needs Replacement

• Refrigerator and Freezer Compartments Are Warm: The interior lights turn on and you can hear the internal evaporator fan blowing, but the temperatures inside are climbing rapidly because the condenser loops cannot reject heat without dynamic airflow.
• Loud Rattling, Growling, or Squealing from the Lower Rear: The bottom back section of the appliance emits a distinct mechanical grinding or high-pitched squealing sound during cooling cycles, indicating collapsed internal sleeve bearings or a bent motor armature shaft.
• The Compressor Cycles Off Rapidly on Thermal Overload: The main compressor runs briefly but shuts off with a sharp metallic "click" after a few minutes because it is overheating from lack of airflow, resulting in zero cooling performance.
• Fan Blade Twitching or Completely Seized: The motor body is hot to the touch and hums faintly under active line voltage, but the armature shaft is seized tight or only twitches erratically due to shorted copper internal field windings.

🔧 Technical Specifications

• Part Number: 242018303
• Part Type: Condenser Cooling Fan Drive Motor
• Electrical Interface: Low-Profile Multi-Pin Quick-Connect Wiring Plug Block
• Condition: Brand New, Genuine Frigidaire OEM Replacement Part
• Brand Compatibility: Precision engineered to fit select premium side-by-side, French-door, and bottom-freezer refrigerators across the Frigidaire, Frigidaire Gallery, Electrolux, Crosley, and Kenmore (select 790/587-series libraries built by Frigidaire) appliance portfolios.

📦 Professional Installation, Care & Maintenance Tips

⚠️ WARNING: POTENTIAL RISK OF LETHAL ELECTRICAL SHOCK AND PHYSICAL ACCIDENTS! The lower machine compartment houses bare high-voltage wiring, high-temperature copper lines, and large compressor start capacitors. **You must completely pull the refrigerator’s heavy utility power plug out from the wall terminal receptacle block, or flip the dedicated utility circuit breakers at your home's main panel box to the absolute OFF position before removing any panel fasteners**. Never service an uncovered machine compartment on an active circuit. Stamped inner steel brackets and cabinet shroud panels feature razor-sharp raw factory borders; **always wear cut-resistant mechanics work gloves and high-impact protective safety glasses throughout this repair procedure**. Pro Tip: Support the Fan Blade Hub Safely and Clean Your Coils! Swapping the condenser fan motor requires pulling the plastic fan blade impeller off the old motor shaft and pressing it onto the new one. **Be incredibly careful when handling the plastic fan blade assembly**. Over time, exposure to machine heat makes the plastic hub brittle; prying near the outer blade edges can easily snap a blade, causing an unbalanced wobble that destroys your new motor. Always grasp the blade structure directly by the thick center hub ring, and slide it straight off the metal armature shaft using steady, parallel pulling force. When installing your brand-new **Frigidaire 242018303** motor, **always hand-drive all structural anchoring hardware manually with basic hand tools**. Utilizing high-torque cordless impact drills can instantly cross-thread the fine metal bracket lines or strip the soft metal receiver holes. **Take this opportunity to thoroughly vacuum all lint, pet hair, and dust off the surrounding condenser wire grids**. Clean coils ensure the fresh motor does not have to work under restrictive static pressure, lowering its operating temperature and significantly extending its functional life. Installation Steps: Fully isolate all incoming electrical power utilities and pull the appliance forward away from the wall to clear a stable work zone. Unthread the hex-head screws fixing the lower rear sheet-metal access shroud panel to the frame and set it aside. Locate the condenser fan motor module next to the compressor dome. Unclip the multi-pin quick-connect wire harness block from the motor lead terminal. Unbolt the screws pinning the primary structural fan mounting bracket to the base pan chassis, and lift the entire bracket-fan module out of the machine cavity. Carefully pull the plastic fan blade straight off the old shaft by its center hub. Unfasten the screws clamping the motor body to the bracket frame, discard the defective motor, and clamp your fresh genuine replacement motor down into the bracket seats using manual hand tools. Push the plastic fan blade hub firmly straight onto the new shaft until it bottoms out securely. Bolt the complete mounting bracket module back down to the machine pan floor, re-clip the wiring harness block until it clicks locked, re-secure the rear access panel cover, restore your utility power line, and verify smooth, whisper-quiet airflow performance.

Specifications

• Type: Condensor Fan Motor
• Country of Origin: China

Condition: Open box