GE WD24X27723 Dishwasher Extension Drain Hose | Genuine OEM Part (Open box)

GE WD24X27723 Dishwasher Extension Drain Hose | Genuine OEM Part (Open box).

GE WD24X27723 Dishwasher Extension Drain Hose

Genuine OEM Corrugated Flexible Grey Drain Hose Extension Line

📝 Product Overview

The GE WD24X27723 is a factory-original replacement flexible extension drain hose line for residential built-in dishwashers. Channeling wastewater directly out of the primary drain pump core, this genuine OEM plumbing tube bridges the gap between your appliance's internal sump exhaust and the under-sink household plumbing drain configuration.

As an Authentic GE Factory Component , this drain line is engineered from high-grade corrugated polypropylene plastic. The specific ribbed pattern optimizes flexible routing through tight cabinetry walls while providing high structural resistance against kinking, collapsing under suction, or cracking from repeated thermal cycles of boiling-hot wash water. The assembly features pre-formed rubberized end cuffs that seal tightly against standard sink drains, garbage disposals, and check-valves under mechanical screw clamps. Opting for a genuine factory line prevents high-pressure blowout leaks, ensures compatibility with your check valve profiles, and stops nasty gray-water backflow odors from bleeding back into your clean wash tub.

🔍 Signs Your Dishwasher Drain Hose Line Needs Replacement

• Visible Cracks, Tears, or Pinholes: Mechanical friction against kitchen wall cutouts or age-related plastic degradation has caused micro-tears, spraying wastewater beneath your cabinetry during the drain cycle.
• Persistent "Foul Odor" and Sluggish Draining: Deep interior grease sludge or chemical scaling has hardened inside the corrugated valleys, causing a permanent blockage or causing grey water to pool at the bottom of the tub.
• Kinked or Collapsed Hose Lines: Pushing the dishwasher too far into its cabinet alcove during a previous repair has collapsed a section of the line, straining the drain pump motor.
• Brittle or Ripped Rubber Connecting End Cuffs: Overtightening screw clamps or dry-rot has split the soft rubber endpoints, rendering it impossible to establish an airtight, watertight seal.

🔧 Technical Specifications

• Part Number: WD24X27723
• Part Type: Flexible Appliance Waste Water Extension Drain Hose Line
• Material Structure: High-density corrugated polypropylene with molded rubber ends
• Color/Finish: Industrial Grey
• Condition: Brand New, Genuine GE OEM Replacement Part
• Brand Compatibility: Precision engineered to fit select modern tall-tub and standard built-in dishwashers across the General Electric, GE Profile, Café, Hotpoint, and Haier corporate brand lines.

📦 Professional Installation, Care & Maintenance Tips

⚠️ WARNING: WATER SPILLAGE AND COMPONENT SLIP HAZARDS — ISOLATE APPLIANCES! Replacing a drain line line interfaces directly with household plumbing circuits. **You must completely close your hot water supply feed line valve and turn off the dishwasher's dedicated electrical circuit breaker at the main breaker box before unfastening any line couplers**. **Keep a shallow catch basin pan and several dry towels directly underneath the line couplers**, as residual rancid water trapped inside the hose will spill out instantly when loosened. Always wear safety glasses and light work gloves to protect your hands from cabinet splinters. Pro Tip: Always Install a "High-Loop" or Air-Gap System! When routing your brand-new **GE WD24X27723** hose to the sink plumbing connection, **you must fasten a section of the line as high as possible beneath the countertop deck (a "High-Loop") before dropping it down into the sink tailpiece or garbage disposal intake**. Without this elevated geometry, dirty sink wastewater will gravitate downward, draining backwards directly into your clean dishwasher chamber. When sliding the rubber cuffs over the sink connection fittings, ensure they slide on fully. Tighten metal gear clamps carefully by hand until snug. **Do not use power tools**, as they can slice right through the soft rubber cuff. If fitting onto a brand-new garbage disposal unit, remember to hammer out and clear the disposal's inner plastic knock-out plug before securing the line. Installation Steps: Completely isolate all water lines and power inputs. Unscrew the lower kickplate shield cover. Disconnect the old drain hose line from the sink plumbing or disposal node and pull it back through the cabinetry side partition. Release the gear clamp fastening the secondary cuff to the drain check-valve under the machine base and pull the failed line clear. Feed the new genuine replacement line back through the cabinet layout. Lubricate the inner rubber sleeve with a dab of liquid dish soap if it feels tight, slide it onto the discharge port terminal tightly, and hand-tighten the screw clamps securely. Route the high-loop under the sink basin, lock the opposite rubber cuff onto your disposal or branch tailpiece, anchor your clamps, open the primary water valves, execute a short rinse cycle, and check with a dry hand to ensure a dry, leak-free repair.

Specifications

• Type: Drain Hose
• Country of Origin: United States

Condition: Open box